THE Latest scope mounts for your Mosin-Tarkov rifle if you want a rock-solid accuracy scope mount while still being able to fire your weapon with the original iron sights. The high-precision low-profile scope mount blends have high quality and the mounting plate design of the first Mosin Tarkov Sniper Rifles with Weaver’s time-tested side-mount design.
Every time, the interlocking mount and plate pattern returns to zero. Because of the quick-detach design, you may also utilize a conventional rifle case. This mount is only compatible with spherical high-wall receivers, the same as the original sniper mounts. The mount is not compatible with hexagonal or spherical receivers with thin walls.
Some Perfect Mosin Tarkov Scope Mounts
The Procedure for Mounting a Mosin Tarkov
Mounting Surfaces Should Be Clean
The first step in mounting your sight is to properly prepare your rifle to accommodate the scope base’s attachment. Place the rifle in a gun vise, on a table, or in another safe/secure area, with the head of the receiver facing up. Use rags or other cushioning to protect the finish. You must have a corresponding one-piece type foundation and screws that are the proper length. Remove any oil, grease, or dirt from the barrel and scope base pieces.
After Removing grease, debris, or dirt that may have caused your scope base to not properly seat onto your rifle, you may decrease each screw hole by removing the cover screws from the top of the receiver. To remove the screws, make sure you use the correct size screwdriver.
Ensure And Level the Playing Field
Replace the rear sight by putting the rifle in a gun vise or on a cushioned bench. Using a wood or fiber dowel and a non-marring hammer, carefully tap the sight base at the dovetail from left to right until the sight is dislodged from the barrel.
Secure your rifle in a vice, lead sled, or other devices after cleaning it. When locking your gun, you’ll also want to level it. All you require for this stage is a short-level you, which can be found in almost every compact toolbox. Adjust your weapon as required by placing the level on top of the receiver.
Install the Base
Using a tiny, thin-bladed gunsmithing screwdriver, replace the filler screws first from the top of the barrel. Place the base on top of the barrel.
Apply tiny gun grease to the contact surfaces before mounting the scope base to your rifle. This will assist prevent rust from accumulating between both the receiver and scope base, depending on the material.
Because the recoil from firing your rifle might cause some of the screws to twist and lose their grip over time, you should contemplate adding a thread locker to the screw and nut. This will guarantee that everything stays in place and that the screws are correctly inserted when tightened.
Use only a thread locker that can be removed. Never apply red or permanent Loctite! Degrees of up to 500°F are required to release a permanent thread locker! Heating your receiver to all those temperatures to remove an optic mount might potentially destroy your rifle unless you’re an experienced blacksmith or gunsmith.
After applying a tiny amount of thread locker and lightly tightening the base, visually and manually verify the receiver to ensure that the screws are not projecting into the action. It’s simple to ensure that the screws don’t strike your bolt by running your fingertips within the action.
Putting the Scope Rings on and Testing the Scope
When once the scope base is properly secured, the scope rings may be installed. To begin, dismantle and precisely organize all of the little screws and excess scope ring pieces so that nothing is lost.
Put screws of the necessary length through the base to verify adequate thread contact, then screw them into the barrel with the appropriate tool. To avoid stripping the barrel threads, ensure that the screw threads correctly connect to the barrel threads.
To ensure that the screws stay tight, many gunsmiths apply a drop of replaceable thread locking compound. Tighten the nuts tightly but not excessively.
You should mount the bottom rings first, then test-fit your sight before attaching the upper rings. When tightening your screws with a Picatinny base, make sure to press the rings as far toward the nearest rail as feasible. This will allow the rings to sit completely against the rail and not shift due to recoil.
After you’ve secured the rifle, insert the scope into the lower pair of scope rings. Check that the scope rings are sufficiently separated from the objective bell and adjustment turrets to enable any necessary adjustments. After determining the best spacing and compliance with the rings, apply the thread locker and manually tighten the screws.
You’ll still need to adjust the eye relief, which is the reason you shouldn’t tighten the screws just yet.
Choosing Eye Relief
Install your scope rings and scope according to the directions that came with your scope rings and/or scope. Always ensure that you have adequate eye relief. Always use a suitable base for the gun and the proper length screws to avoid gun damage.
Setting the eye relief correctly will help to prevent the black halo that might appear while looking through a rifle sight. Pick up your rifle and shoulder it as if you were going to use it in the field. The difficulty here is to shoulder the gun while closing your eyes. Then, locate a comfortable location to put your face on your stock’s comb. This will assist you in locating the natural location of your firearm. You will not rely on the optic to help you position your head.
As once the rifle is comfortably shoulderable, open your eyes and check for proper eye relief. To find the sweet spot, adjust the scope by sliding it gently forward or backward. When positioned at the proper distance, you should have a clear field of view.
If you continue to notice a black halo via your scope, don’t be scared to reposition your scope rings. Depending on your setup, you might need to give yourself a bit more or less wiggle room.
Check Here Price: Monstrum Cantilever Picatinny Scope Mount
Increasing Your Scope
It’s time to level the scope after you’ve determined the best position for your eye relief.
Place your level on the central turret and secure the rifle once again. Adjust your sight so that the reticle is perpendicular and parallel to your bore. Making sure your reticle is level will allow you to correctly compensate for windage and height in the field.
After the scope has been installed and leveled, twist all of the scope ring screws. Stiffen each screw in a cross pattern, as if fitting a tire. This ensures that the rings are positioned evenly on the front and back of the scope. Allow the thread locker to cure completely before firing any rounds for the optimum grip.
read more: how to mount scope on AR50
Your New Scope’s Ocular Focus and Sighting
You should correctly tune in ocular focus before sighting in your new scope. The goal of adjusting the ocular focus is to obtain a sharp and clear view of your scope’s reticle.
Our eyes can focus on a reticle that is slightly out of focus, but this causes strain on your eye muscles. If the reticle is not correctly set, this might cause eye fatigue.
You may adjust the scope diopter by aiming your unloaded rifle at a high-contrast backdrop until your reticle is clearly in focus.
Is it possible to mount a scope on Mosin Tarkov?
PU 3.5 range Kochetov Mount, designed specifically for Mosin rifles, permits the installation of a PU 3.5 scope on a rifle.
Can you attach a scope to a Mosin Infantry Tarkov?
The Tri-Rail and MNG mounts do not function with it, however, they do with the Mosin Infantry rifle. The scope mounts are incompatible because the carbine length Mosin has a distinct rear sight than the full-size Mosin.
Could a hunting scope be mounted on a Mosin?
No. The only sniper accessible, the Mosin tarkov, had a long-range sight, but it was removed since the weapon lacked a rail system capable of supporting current technology.
Which Mosin ammo tarkov is the best?
SNB. If available, the top-tier choice and greatest Mosin ammunition Tarkov has to give will pass through any armor and strike hard when it does.
Is Mosin a decent tarkov?
The Mosin is a lousy gun; it has poor ergonomics and accuracy compared to other bolt-action rifles and can only be loaded from the top. The Mosin’s only advantage was that it could kill players in a single hit to the thorax, especially if they were wearing armor.
Hey, This is Ebert Alberts. I’m the sole writer and creator of all the content you’ll find on this site. I’ve been passionate about shooting with scopes, red dot sights, and all kinds of gun optics for years now. And during that time, I’ve learned a lot – often the hard way. I’ve wasted thousands of dollars on scopes that turned out to be duds, and I’ve also found some real gems along the way.